view src/gccache-gtk.c @ 665:fdefd0186b75

[xemacs-hg @ 2001-09-20 06:28:42 by ben] The great integral types renaming. The purpose of this is to rationalize the names used for various integral types, so that they match their intended uses and follow consist conventions, and eliminate types that were not semantically different from each other. The conventions are: -- All integral types that measure quantities of anything are signed. Some people disagree vociferously with this, but their arguments are mostly theoretical, and are vastly outweighed by the practical headaches of mixing signed and unsigned values, and more importantly by the far increased likelihood of inadvertent bugs: Because of the broken "viral" nature of unsigned quantities in C (operations involving mixed signed/unsigned are done unsigned, when exactly the opposite is nearly always wanted), even a single error in declaring a quantity unsigned that should be signed, or even the even more subtle error of comparing signed and unsigned values and forgetting the necessary cast, can be catastrophic, as comparisons will yield wrong results. -Wsign-compare is turned on specifically to catch this, but this tends to result in a great number of warnings when mixing signed and unsigned, and the casts are annoying. More has been written on this elsewhere. -- All such quantity types just mentioned boil down to EMACS_INT, which is 32 bits on 32-bit machines and 64 bits on 64-bit machines. This is guaranteed to be the same size as Lisp objects of type `int', and (as far as I can tell) of size_t (unsigned!) and ssize_t. The only type below that is not an EMACS_INT is Hashcode, which is an unsigned value of the same size as EMACS_INT. -- Type names should be relatively short (no more than 10 characters or so), with the first letter capitalized and no underscores if they can at all be avoided. -- "count" == a zero-based measurement of some quantity. Includes sizes, offsets, and indexes. -- "bpos" == a one-based measurement of a position in a buffer. "Charbpos" and "Bytebpos" count text in the buffer, rather than bytes in memory; thus Bytebpos does not directly correspond to the memory representation. Use "Membpos" for this. -- "Char" refers to internal-format characters, not to the C type "char", which is really a byte. -- For the actual name changes, see the script below. I ran the following script to do the conversion. (NOTE: This script is idempotent. You can safely run it multiple times and it will not screw up previous results -- in fact, it will do nothing if nothing has changed. Thus, it can be run repeatedly as necessary to handle patches coming in from old workspaces, or old branches.) There are two tags, just before and just after the change: `pre-integral-type-rename' and `post-integral-type-rename'. When merging code from the main trunk into a branch, the best thing to do is first merge up to `pre-integral-type-rename', then apply the script and associated changes, then merge from `post-integral-type-change' to the present. (Alternatively, just do the merging in one operation; but you may then have a lot of conflicts needing to be resolved by hand.) Script `fixtypes.sh' follows: ----------------------------------- cut ------------------------------------ files="*.[ch] s/*.h m/*.h config.h.in ../configure.in Makefile.in.in ../lib-src/*.[ch] ../lwlib/*.[ch]" gr Memory_Count Bytecount $files gr Lstream_Data_Count Bytecount $files gr Element_Count Elemcount $files gr Hash_Code Hashcode $files gr extcount bytecount $files gr bufpos charbpos $files gr bytind bytebpos $files gr memind membpos $files gr bufbyte intbyte $files gr Extcount Bytecount $files gr Bufpos Charbpos $files gr Bytind Bytebpos $files gr Memind Membpos $files gr Bufbyte Intbyte $files gr EXTCOUNT BYTECOUNT $files gr BUFPOS CHARBPOS $files gr BYTIND BYTEBPOS $files gr MEMIND MEMBPOS $files gr BUFBYTE INTBYTE $files gr MEMORY_COUNT BYTECOUNT $files gr LSTREAM_DATA_COUNT BYTECOUNT $files gr ELEMENT_COUNT ELEMCOUNT $files gr HASH_CODE HASHCODE $files ----------------------------------- cut ------------------------------------ `fixtypes.sh' is a Bourne-shell script; it uses 'gr': ----------------------------------- cut ------------------------------------ #!/bin/sh # Usage is like this: # gr FROM TO FILES ... # globally replace FROM with TO in FILES. FROM and TO are regular expressions. # backup files are stored in the `backup' directory. from="$1" to="$2" shift 2 echo ${1+"$@"} | xargs global-replace "s/$from/$to/g" ----------------------------------- cut ------------------------------------ `gr' in turn uses a Perl script to do its real work, `global-replace', which follows: ----------------------------------- cut ------------------------------------ : #-*- Perl -*- ### global-modify --- modify the contents of a file by a Perl expression ## Copyright (C) 1999 Martin Buchholz. ## Copyright (C) 2001 Ben Wing. ## Authors: Martin Buchholz <martin@xemacs.org>, Ben Wing <ben@xemacs.org> ## Maintainer: Ben Wing <ben@xemacs.org> ## Current Version: 1.0, May 5, 2001 # This program is free software; you can redistribute it and/or modify # it under the terms of the GNU General Public License as published by # the Free Software Foundation; either version 2, or (at your option) # any later version. # # This program is distributed in the hope that it will be useful, but # WITHOUT ANY WARRANTY; without even the implied warranty of # MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU # General Public License for more details. # # You should have received a copy of the GNU General Public License # along with XEmacs; see the file COPYING. If not, write to the Free # Software Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA # 02111-1307, USA. eval 'exec perl -w -S $0 ${1+"$@"}' if 0; use strict; use FileHandle; use Carp; use Getopt::Long; use File::Basename; (my $myName = $0) =~ s@.*/@@; my $usage=" Usage: $myName [--help] [--backup-dir=DIR] [--line-mode] [--hunk-mode] PERLEXPR FILE ... Globally modify a file, either line by line or in one big hunk. Typical usage is like this: [with GNU print, GNU xargs: guaranteed to handle spaces, quotes, etc. in file names] find . -name '*.[ch]' -print0 | xargs -0 $0 's/\bCONST\b/const/g'\n [with non-GNU print, xargs] find . -name '*.[ch]' -print | xargs $0 's/\bCONST\b/const/g'\n The file is read in, either line by line (with --line-mode specified) or in one big hunk (with --hunk-mode specified; it's the default), and the Perl expression is then evalled with \$_ set to the line or hunk of text, including the terminating newline if there is one. It should destructively modify the value there, storing the changed result in \$_. Files in which any modifications are made are backed up to the directory specified using --backup-dir, or to `backup' by default. To disable this, use --backup-dir= with no argument. Hunk mode is the default because it is MUCH MUCH faster than line-by-line. Use line-by-line only when it matters, e.g. you want to do a replacement only once per line (the default without the `g' argument). Conversely, when using hunk mode, *ALWAYS* use `g'; otherwise, you will only make one replacement in the entire file! "; my %options = (); $Getopt::Long::ignorecase = 0; &GetOptions ( \%options, 'help', 'backup-dir=s', 'line-mode', 'hunk-mode', ); die $usage if $options{"help"} or @ARGV <= 1; my $code = shift; die $usage if grep (-d || ! -w, @ARGV); sub SafeOpen { open ((my $fh = new FileHandle), $_[0]); confess "Can't open $_[0]: $!" if ! defined $fh; return $fh; } sub SafeClose { close $_[0] or confess "Can't close $_[0]: $!"; } sub FileContents { my $fh = SafeOpen ("< $_[0]"); my $olddollarslash = $/; local $/ = undef; my $contents = <$fh>; $/ = $olddollarslash; return $contents; } sub WriteStringToFile { my $fh = SafeOpen ("> $_[0]"); binmode $fh; print $fh $_[1] or confess "$_[0]: $!\n"; SafeClose $fh; } foreach my $file (@ARGV) { my $changed_p = 0; my $new_contents = ""; if ($options{"line-mode"}) { my $fh = SafeOpen $file; while (<$fh>) { my $save_line = $_; eval $code; $changed_p = 1 if $save_line ne $_; $new_contents .= $_; } } else { my $orig_contents = $_ = FileContents $file; eval $code; if ($_ ne $orig_contents) { $changed_p = 1; $new_contents = $_; } } if ($changed_p) { my $backdir = $options{"backup-dir"}; $backdir = "backup" if !defined ($backdir); if ($backdir) { my ($name, $path, $suffix) = fileparse ($file, ""); my $backfulldir = $path . $backdir; my $backfile = "$backfulldir/$name"; mkdir $backfulldir, 0755 unless -d $backfulldir; print "modifying $file (original saved in $backfile)\n"; rename $file, $backfile; } WriteStringToFile ($file, $new_contents); } } ----------------------------------- cut ------------------------------------ In addition to those programs, I needed to fix up a few other things, particularly relating to the duplicate definitions of types, now that some types merged with others. Specifically: 1. in lisp.h, removed duplicate declarations of Bytecount. The changed code should now look like this: (In each code snippet below, the first and last lines are the same as the original, as are all lines outside of those lines. That allows you to locate the section to be replaced, and replace the stuff in that section, verifying that there isn't anything new added that would need to be kept.) --------------------------------- snip ------------------------------------- /* Counts of bytes or chars */ typedef EMACS_INT Bytecount; typedef EMACS_INT Charcount; /* Counts of elements */ typedef EMACS_INT Elemcount; /* Hash codes */ typedef unsigned long Hashcode; /* ------------------------ dynamic arrays ------------------- */ --------------------------------- snip ------------------------------------- 2. in lstream.h, removed duplicate declaration of Bytecount. Rewrote the comment about this type. The changed code should now look like this: --------------------------------- snip ------------------------------------- #endif /* The have been some arguments over the what the type should be that specifies a count of bytes in a data block to be written out or read in, using Lstream_read(), Lstream_write(), and related functions. Originally it was long, which worked fine; Martin "corrected" these to size_t and ssize_t on the grounds that this is theoretically cleaner and is in keeping with the C standards. Unfortunately, this practice is horribly error-prone due to design flaws in the way that mixed signed/unsigned arithmetic happens. In fact, by doing this change, Martin introduced a subtle but fatal error that caused the operation of sending large mail messages to the SMTP server under Windows to fail. By putting all values back to be signed, avoiding any signed/unsigned mixing, the bug immediately went away. The type then in use was Lstream_Data_Count, so that it be reverted cleanly if a vote came to that. Now it is Bytecount. Some earlier comments about why the type must be signed: This MUST BE SIGNED, since it also is used in functions that return the number of bytes actually read to or written from in an operation, and these functions can return -1 to signal error. Note that the standard Unix read() and write() functions define the count going in as a size_t, which is UNSIGNED, and the count going out as an ssize_t, which is SIGNED. This is a horrible design flaw. Not only is it highly likely to lead to logic errors when a -1 gets interpreted as a large positive number, but operations are bound to fail in all sorts of horrible ways when a number in the upper-half of the size_t range is passed in -- this number is unrepresentable as an ssize_t, so code that checks to see how many bytes are actually written (which is mandatory if you are dealing with certain types of devices) will get completely screwed up. --ben */ typedef enum lstream_buffering --------------------------------- snip ------------------------------------- 3. in dumper.c, there are four places, all inside of switch() statements, where XD_BYTECOUNT appears twice as a case tag. In each case, the two case blocks contain identical code, and you should *REMOVE THE SECOND* and leave the first.
author ben
date Thu, 20 Sep 2001 06:31:11 +0000
parents 0784d089fdc9
children 2923009caf47
line wrap: on
line source

/* Efficient caching of Gtk GCs (graphics contexts).
   Copyright (C) 1993 Free Software Foundation, Inc.
   Copyright (C) 1994, 1995 Board of Trustees, University of Illinois.

This file is part of XEmacs.

XEmacs is free software; you can redistribute it and/or modify it
under the terms of the GNU General Public License as published by the
Free Software Foundation; either version 2, or (at your option) any
later version.

XEmacs is distributed in the hope that it will be useful, but WITHOUT
ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
for more details.

You should have received a copy of the GNU General Public License
along with XEmacs; see the file COPYING.  If not, write to
the Free Software Foundation, Inc., 59 Temple Place - Suite 330,
Boston, MA 02111-1307, USA.  */

/* Synched up with: Not in FSF. */

/* Emacs uses a lot of different display attributes; for example, assume
   that only four fonts are in use (normal, bold, italic, and bold-italic).
   Then assume that one stipple or background is used for text selections,
   and another is used for highlighting mousable regions.  That makes 16
   GCs already.  Add in the fact that another GC may be needed to display
   the text cursor in any of those regions, and you've got 32.  Add in
   more fonts, and it keeps increasing exponentially.

   We used to keep these GCs in a cache of merged (fully qualified) faces.
   However, a lot of other code in xterm.c used XChangeGC of existing GCs,
   which is kind of slow and kind of random.  Also, managing the face cache
   was tricky because it was hard to know when a face was no longer visible
   on the frame -- we had to mark all frames as garbaged whenever a face
   was changed, which caused an unpleasant amount of flicker (since faces are
   created/destroyed (= changed) whenever a frame is created/destroyed.

   So this code maintains a cache at the GC level instead of at the face
   level.  There is an upper limit on the size of the cache, after which we
   will stop creating GCs and start reusing them (reusing the least-recently-
   used ones first).  So if faces get changed, their GCs will eventually be
   recycled.  Also more sharing of GCs is possible.

   This code uses hashtables.  It could be that, if the cache size is small
   enough, a linear search might be faster; but I doubt it, since we need
   `equal' comparisons, not `eq', and I expect that the optimal cache size
   will be ~100.

   Written by jwz, 14 jun 93
   Hacked by William Perry, apr 2000
 */

#include <config.h>
#include <gtk/gtk.h>
#include "lisp.h"
#include "gccache-gtk.h"

#define GC_CACHE_SIZE 100

#define GCCACHE_HASH

#ifdef GCCACHE_HASH
#include "lisp.h"
#include "hash.h"
#endif

struct gcv_and_mask {
	GdkGCValues gcv;
	GdkGCValuesMask mask;
};

struct gc_cache_cell {
  GdkGC *gc;
  struct gcv_and_mask gcvm;
  struct gc_cache_cell *prev, *next;
};

struct gc_cache {
  GdkWindow *window;	/* used only as arg to XCreateGC */
  int size;
  struct gc_cache_cell *head;
  struct gc_cache_cell *tail;
#ifdef GCCACHE_HASH
  struct hash_table * table;
#endif

  int create_count;
  int delete_count;
};

#ifdef GCCACHE_HASH
static unsigned long
gc_cache_hash (const void *arg)
{
  const struct gcv_and_mask *gcvm = (const struct gcv_and_mask *) arg;
  unsigned long *longs = (unsigned long *) &gcvm->gcv;
  unsigned long hash = gcvm->mask;
  int i;
  /* This could look at the mask and only use the used slots in the
     hash code.  That would win in that we wouldn't have to initialize
     every slot of the gcv when calling gc_cache_lookup.  But we need
     the hash function to be as fast as possible; some timings should
     be done. */
  for (i = 0; i < (sizeof (GdkGCValues) / sizeof (unsigned long)); i++)
    hash = (hash<<1) ^ *longs++;
  return hash;
}

#endif /* GCCACHE_HASH */

static int
gc_cache_eql (const void *arg1, const void *arg2)
{
  /* See comment in gc_cache_hash */
  const struct gcv_and_mask *gcvm1 = (const struct gcv_and_mask *) arg1;
  const struct gcv_and_mask *gcvm2 = (const struct gcv_and_mask *) arg2;

  return !memcmp(&gcvm1->gcv, &gcvm2->gcv, sizeof(gcvm1->gcv))
    && gcvm1->mask == gcvm2->mask;
}

struct gc_cache *
make_gc_cache (GtkWidget *widget)
{
  struct gc_cache *cache = xnew (struct gc_cache);
  cache->window = widget->window;
  cache->size = 0;
  cache->head = cache->tail = 0;
  cache->create_count = cache->delete_count = 0;
#ifdef GCCACHE_HASH
  cache->table =
    make_general_hash_table (GC_CACHE_SIZE, gc_cache_hash, gc_cache_eql);
#endif
  return cache;
}

void
free_gc_cache (struct gc_cache *cache)
{
  struct gc_cache_cell *rest, *next;
  rest = cache->head;
  while (rest)
    {
      gdk_gc_destroy(rest->gc);
      next = rest->next;
      xfree (rest);
      rest = next;
    }
#ifdef GCCACHE_HASH
  free_hash_table (cache->table);
#endif
  xfree (cache);
}

GdkGC *
gc_cache_lookup (struct gc_cache *cache, GdkGCValues *gcv, GdkGCValuesMask mask)
{
  struct gc_cache_cell *cell, *next, *prev;
  struct gcv_and_mask gcvm;

  if ((!!cache->head) != (!!cache->tail)) abort ();
  if (cache->head && (cache->head->prev || cache->tail->next)) abort ();

  /* Gdk does not have the equivalent of 'None' for the clip_mask, so
     we need to check it carefully, or gdk_gc_new_with_values will
     coredump */
  if ((mask & GDK_GC_CLIP_MASK) && !gcv->clip_mask)
  {
      mask &= ~GDK_GC_CLIP_MASK;
  }

  gcvm.mask = mask;
  gcvm.gcv = *gcv;	/* this copies... */

#ifdef GCCACHE_HASH

  if (gethash (&gcvm, cache->table, (const void **) &cell))

#else /* !GCCACHE_HASH */

  cell = cache->tail;	/* start at the end (most recently used) */
  while (cell)
    {
      if (gc_cache_eql (&gcvm, &cell->gcvm))
	break;
      else
	cell = cell->prev;
    }

  /* #### This whole file needs some serious overhauling. */
  if (!(mask | GDK_GC_TILE) && cell->gcvm.gcv.tile)
    cell = 0;
  else if (!(mask | GDK_GC_STIPPLE) && cell->gcvm.gcv.stipple)
    cell = 0;

  if (cell)

#endif /* !GCCACHE_HASH */

    {
      /* Found a cell.  Move this cell to the end of the list, so that it
	 will be less likely to be collected than a cell that was accessed
	 less recently.
       */
      if (cell == cache->tail)
	return cell->gc;

      next = cell->next;
      prev = cell->prev;
      if (prev) prev->next = next;
      if (next) next->prev = prev;
      if (cache->head == cell) cache->head = next;
      cell->next = 0;
      cell->prev = cache->tail;
      cache->tail->next = cell;
      cache->tail = cell;
      if (cache->head == cell) abort ();
      if (cell->next) abort ();
      if (cache->head->prev) abort ();
      if (cache->tail->next) abort ();
      return cell->gc;
    }

  /* else, cache miss. */

  if (cache->size == GC_CACHE_SIZE)
    /* Reuse the first cell on the list (least-recently-used).
       Remove it from the list, and unhash it from the table.
     */
    {
      cell = cache->head;
      cache->head = cell->next;
      cache->head->prev = 0;
      if (cache->tail == cell) cache->tail = 0; /* only one */
      gdk_gc_destroy (cell->gc);
      cache->delete_count++;
#ifdef GCCACHE_HASH
      remhash (&cell->gcvm, cache->table);
#endif
    }
  else if (cache->size > GC_CACHE_SIZE)
    abort ();
  else
    {
      /* Allocate a new cell (don't put it in the list or table yet). */
      cell = xnew (struct gc_cache_cell);
      cache->size++;
    }

  /* Now we've got a cell (new or reused).  Fill it in. */
  memcpy (&cell->gcvm.gcv, gcv, sizeof (GdkGCValues));
  cell->gcvm.mask = mask;

  /* Put the cell on the end of the list. */
  cell->next = 0;
  cell->prev = cache->tail;
  if (cache->tail) cache->tail->next = cell;
  cache->tail = cell;
  if (! cache->head) cache->head = cell;

  cache->create_count++;
#ifdef GCCACHE_HASH
  /* Hash it in the table */
  puthash (&cell->gcvm, cell, cache->table);
#endif

  /* Now make and return the GC. */
  cell->gc = gdk_gc_new_with_values (cache->window, gcv, mask);

  /* debug */
  assert (cell->gc == gc_cache_lookup (cache, gcv, mask));

  return cell->gc;
}